Harrison Hydra-Gen Model 6.0MAS-16R

One (1) Harrison Hydraulic Driven Generator model number 6.0MAS-16R rated at 6000 watts, 25/50 amps, 120/240VAC, 60Hz, 1-phase.  The system shall be designed and assembled by a company with no less than 10 years experience in the manufacture of hydraulic driven generators.  The system shall be tested at the full nameplate load prior to shipping and be accompanied with the test report.  The test report will document the generator’s performance at various loads from no load to full load to ensure reliable power delivery at those loads. 

The motor/generator shall be placed in a frame which affords protection to the components and provides a unitized mounting module containing the motor/generator, reservoir, oil cooler, filtration, on/off manifold containing a cross port check valve allowing unit to be started and shut down remotely.  The generator shall be a commercial type with a heavy-duty bearing and of brushless design to ensure low maintenance.  No brushes or slip rings shall be allowed.  The reservoir shall include an oil level sight gauge, oil temperature gauge, fill cap, oil filter, and a venturi boost unit to provide positive pressure to the pump suction port.  The generator and motor shall be close coupled and aligned using a Morse taper with a through bolt to secure the motor to the generator.  No two (2) bearing generators shall be permitted.

The system must be capable of producing the full nameplate power when driven from the vehicle PTO from idle to maximum engine speed.  The generator system must be able to operate on either a Constant Engaged PTO or a Hot Shift PTO.  Determination as to which PTO to use will be made by the Fire Department.  The generator must be able to be used while vehicle is either stationary or in motion.

The hydraulic motor and pump shall be of axial piston design to provide low internal leakage and a high degree of frequency stability.  No gear pumps or motors will be used.  The pump shall match the system with the proper orifice, pressure compensator, and load sense settings to provide stable output regardless of engine rpm or electrical load demands.

The system shall be capable of normal operations using a commonly available ATF fluid, such as GM Dextron II or equivalent.  All fluid service points shall be in close proximity to the reservoir for ease of scheduled maintenance.

When properly installed, the system shall be warranted for a period of not less than two (2) years or 2000 hours, whichever should come first.

The generator shall be able to remotely turn systems full kW on or off without regard to engine RPM by using a 12VDC switch.  The switch will be mounted as directed by the fire department. 

Both the 8.0MAS and 10.0MAS specifications are the same as the 6.0MAS with the following exceptions:

Harrison Hydra-Gen model 8.0MAS-16R

One (1) Harrison Hydraulic Driven Generator model number 8.0MAS-16R rated at 8000 watts, 34/68 amps, 120/240VAC, 60Hz, 1-phase.

A Quadra meter containing the volt, amp, and frequency is to be provided and installed in a location, which is away from the weather and water over spray.  If the meter is to be installed in the elements then a weatherproof digital meter is to be used.

Harrison Hydra-Gen model 10.0MAS-16R

One (1) Harrison Hydraulic Driven Generator model number 10.0MAS-16R rated at 10000 watts, 42/84 amps, 120/240VAC, 60Hz, 1-phase.

A Quadra meter containing the volt, amp, and frequency is to be provided and installed in a location, which is away from the weather and water over spray.  If the meter is to be installed in the elements then a weatherproof digital meter is to be used.

Harrison Hydra-Gen 6.0 – 10.0 MAS-16R/5 Specifications

DIMENSIONS:  Reservoirs are shipped attached, but can be remote mounted.  (Tray Unit dimensions and weights are without the reservoir)

ALTERNATOR DETAIL:

HYDRAULIC SYSTEM:

HYDRUALIC PUMP: Standard Pump Specification

PUMP 45 CC Dimensions

Tray Dimensions