Harrison Hydra-Gen model 10.0MPC-16D Specifications
One (1) Harrison Hydraulic Driven Generator model number 10.0MPC-16D rated at 10000 watts, 42/83 amps, 120/240VAC, 60Hz, 1-phase. The system shall be designed and assembled by a company with no less than 10 years experience in the manufacture of hydraulic driven generators. The system shall be tested at the full nameplate load prior to shipping and be accompanied with the test report. The test report will document the generator’s performance at various loads from no load to full load to ensure reliable power delivery at those loads.
The motor/generator shall be placed in a frame which affords protection to the components and provides a unitized mounting module containing the motor/generator, reservoir, oil cooler, filtration, manifold containing a cross port check valve and relief valve. The generator shall be a continuous duty, industrial type with a heavy-duty bearing and of brushless design to ensure low maintenance. No brushes or slip rings will be allowed. The reservoir shall include an oil level sight gauge, oil temperature gauge, fill cap, oil filter, low fluid level sensor, high temperature sensor and a venturi boost unit to provide positive pressure to the pump suction port. The generator and motor shall be close coupled and aligned using a single bearing alternator design. No two (2) bearing generators shall be permitted
The system must be capable of producing the full nameplate power when driven from the vehicle PTO from idle to maximum engine speed. The generator system must be able to operate on either a Constant Engaged PTO or a Hot Shift PTO. Determination as to which PTO to use will be made by the Fire Department. The generator must be able to be used while vehicle is either stationary or in motion.
The hydraulic motor and pump shall be of axial piston design to provide low internal leakage and a high degree of frequency stability. No gear pumps or motors will be used. The pump shall match the system with the proper orifice, pressure compensator, and load sense settings to provide stable output regardless of engine rpm or electrical load demands.
The system shall be capable of normal operations using a commonly available ATF fluid, such as GM Dextron II, III, or equivalent. All fluid service points shall be in close proximity to the reservoir for ease of scheduled maintenance.
When properly installed, the system shall be warranted for a period of not less than two (2) years or 2000 hours, whichever should come first.
A Quadra meter containing the volt, amp, and frequency is to be provided and installed in a location, which is away from the weather and water over spray. If the meter is to be installed in the elements then a weatherproof digital meter is to be used.
Both the 15.0MPC and 20.0MPC specifications are the same as the 10.0MPC with the following exceptions:
Harrison Hydra-Gen model 15.0MPC-16D
One (1) Harrison Hydraulic Driven Generator model number 15.0MPC-16D rated at 15000 watts, 62/125 amps, 120/240VAC, 60Hz, 1-phase.
Harrison Hydra-Gen model 20.0MPC-16D
One (1) Harrison Hydraulic Driven Generator model number 20.0MPC-16D rated at 20000 watts, 83/166 amps, 120/240VAC, 60Hz, 1-phase.
Harrison Hydra-Gen 10.0 – 20.0MPC-16/3 Specifications
DIMENSIONS: Reservoirs are shipped attached, but can be remote mounted. (Tray Unit dimensions and weights are without the reservoir)
|
10.0 MPC |
15.0 MPC |
20.0 MPC |
Reservoir |
Length |
23” |
23” |
23” |
22.5” |
Width |
29” |
29” |
29” |
6” |
Height |
19” |
19” |
19” |
18.5” |
Weight |
367 lbs |
437 lbs |
488 lbs |
24 lbs |
|
|
|
|
|
Max KW |
10.0 |
15.0 |
20.0 |
|
Amps @ 120V |
84 |
125 |
167 |
|
Amps @ 240V |
42 |
62 |
84 |
|
HP Required |
24 |
34 |
48 |
|
Torque Required |
87.5 |
131.3 |
170.3 |
|
Max System PSI |
2150 |
3150 |
4400 |
|
ALTERNATOR DETAIL
| Design |
Brushless revolving field, four pole, 1800 rpm for 60 hertz operation. |
| Rating |
See nameplate for individual rating. |
| Regulation |
+/- 1% Voltage regulation from nameplate rating. |
| Waveform |
Harmonic distortion is limited to just 4 % |
| Insulation |
Class H, 200° C, Slot Insulation, Varnish. Additional Marine Coating. |
| Power Factor |
1.0 (unity) for single – phase units, 0.8 for three phase units. |
HYDRAULIC SYSTEM
| Type of oil: |
Use only premium hydraulic fluid with anti wear, anti foam, and anti rust additives. Optimum operating viscosity is 80-170 SSU. Viscosity should never exceed 4,600 SSU at the coldest startup temperature, and never less than 60 SSU at 180 degrees F. |
| Capacity: |
The reservoir should contain 7.5 gallons (U.S.) of hydraulic fluid. |
HYDRUALIC PUMP: Standard Pump Specification
| |
Minimum Shaft Speed
(10-20 MPC) |
800 RPM |
| |
Maximum Shaft Speed
(Note: for speeds above 3000 rpm consult Harrison Hydra-Gen factory) |
3000 RPM |
| |
Displacement |
80 CC |
| |
Max. Temperature |
204° F |
| |
Min. Temperature |
-4° F |
| |
Weight of Pump |
78 lbs |
| |
Max. Torque |
295 ft. lbs |
| |
Pump shaft |
SAE “C” Spline or Keyed |
| |
Rotation |
CW or CCW |
| |
Max. Pressure |
4600 psi |
| |
Max. Vacuum |
10.0 in. hg. |
80cc Pump Dimensions

Optional 80 cc Hydraulic Pump Dimensions 
Tray Dimensions

|